当前位置: 首页- 新闻资讯

铝板使用中要注意什么?

来源://www.renttoplux.com/发布时间:2024-01-23

铝板存放:应存放在干燥通风的地方,并平放在表面,不要踩踏、撞击。

Aluminum plate storage: It should be stored in a dry and ventilated place, and placed flat on the surface, without stepping or hitting.

铝板搬运:板的四周应同时抬起,以免划伤板的表面。

Aluminum plate handling: The edges of the plate should be lifted simultaneously to avoid scratching the surface of the plate.

铝板切槽:用插床或锣机切槽时,应使用半圆头铣刀。无论对铝板的损伤是否太深,也不太浅,不易折叠,0.2-0.3mm厚的塑料芯应与铝板一起弯曲,以增加强度和韧性,否则铝板弯曲时可能断裂或漆膜破裂。

Aluminum plate groove cutting: When using a slotting machine or gong machine to cut grooves, a semi-circular end milling cutter should be used. Regardless of whether the damage to the aluminum plate is too deep, not too shallow, and not easy to fold, plastic cores with a thickness of 0.2-0.3mm should be bent together with the aluminum plate to increase strength and toughness, otherwise the aluminum plate may break or the paint film may break when bent.

20230511085244839.jpg

铝板弯曲:弯曲边缘时,应力均匀,成型一次,不要反复弯曲,否则铝板可能断裂。

Aluminum plate bending: When bending the edges, the stress should be uniform and formed once. Do not bend repeatedly, otherwise the aluminum plate may break.

铝板电弧加工:应采用专用弯曲设备对电弧进行加工,使板材逐渐达到所需的表面,不得一次弯曲。

Aluminum plate arc processing: Special bending equipment should be used to process the arc, so that the plate gradually reaches the required surface and cannot be bent in one go.

铝板批次:同一类型不同批次的铝板可能存在色差。在销售和使用不同批次的纸张时,应增加色差比较程序。

Aluminum plate batch: There may be color differences between aluminum plates of the same type in different batches. When selling and using different batches of paper, a color difference comparison program should be added.

铝板安装方向:同色铝板安装在同一平面上时,流向应一致,否则会产生视觉色差。

Aluminum plate installation direction: When the same colored aluminum plate is installed on the same plane, the flow direction should be consistent, otherwise it will cause visual color difference.

铝板撕膜:铝板安装后45天内撕下保护膜,否则撕膜困难或发生胶转移。

Aluminum plate film tearing: Remove the protective film from the aluminum plate within 45 days after installation, otherwise it will be difficult to tear the film or adhesive transfer may occur.

铝板使用条件:室内墙板应在室内使用,不得安装在室外,以保证使用效果和使用寿命。

Aluminum panel usage conditions: Indoor wall panels should be used indoors and not installed outdoors to ensure their effectiveness and lifespan.

本文由铝板生产厂家提供技术支持,更多的详细精彩内容请点击我们的网站//www.renttoplux.com我们将会全心全意为您提供满意的服务。

This article is supported by aluminum plate manufacturers. For more detailed and exciting content, please click on our website //www.renttoplux.com We will wholeheartedly provide you with satisfactory service.

Baidu
map